Short answer
Water that shows up above a bay window only when it rains is coming in from outside, not from plumbing. The leak is almost always failed flashing or cracked sealant where the bay roof meets the wall, or the joint where the window meets the siding. Reseal and repair that exterior joint and the inside stays dry. If water appears on dry days too, the source is a pipe or a drain instead.
Tell a rain leak from a plumbing leak first
- Note when the water appears. Water that shows only in or after rain is coming from outside. Water that shows up on a dry day is a pipe or a drain.
- Take a wide photo inside. Include the window, the trim above it, and the wall on both sides so the wet path is visible.
- Look outside at the bay roof. Check the cap or flashing where it meets the wall, and the sealant line along each side of the window.
- Press the joints with a screwdriver tip. Cracked, lifted or missing sealant is the leak. Loose or rusted flashing needs re-securing.
- Check the window frame and trim. Wood that sinks in or crumbles, or a frame that moves when pushed, means water has been getting in for a while.
- Press the wall and ceiling inside. Firm and dry is cosmetic. Soft, spongy or stained means the wall behind is wet.
If the water only appears in rain and the exterior joint is cracked or open, reseal and repair that joint. If the water shows on dry days too, treat it as a plumbing leak and find the supply line first.
Repair or replace
| Situation | What to do |
|---|---|
| Failed sealant at the bay roof or window edge | Reseal. Cut the old sealant out, clean the joint, and apply new exterior-grade sealant. |
| Lifted or rusted flashing | Repair. Re-secure or replace the flashing so water sheds off the joint. |
| Frame or trim soft and rotten | Replace the rotten wood first, then reseal. New sealant over rot fails. |
| Wall or ceiling behind the window soft or stained | Open and dry the wall, repair the drywall, then fix the exterior joint. |
| Window unit itself failed or will not close and seal | Replace the unit. A window that no longer seals gets swapped. |
What it costs
Runhome contractor estimates for investigating and repairing a bay window leak ran from $355 to $790 as of November 2026, including the trip and assessment.
| Option | Range |
|---|---|
| Inspect the leak and repair the exterior flashing or sealant | $355 to $790 |
Can I do it myself?
You can reseal a joint if the flashing is sound and you can reach it safely from a ladder at ground level. Clean the old sealant out, let the joint dry, and run a bead of exterior-grade sealant over it. Hire for this if the work is above the first floor, on the bay roof, or if the flashing itself is loose or rusted, because a bead of sealant is only as good as the flashing under it. Hire as well if the wall inside is soft or stained, since that water damage has to be opened and dried before any seal closes the leak.
What a contractor will ask you
Have these ready and you skip the back-and-forth.
- Which window leaks, with a photo from inside and from outside.
- When the leak started, and whether it follows heavy storms or every rain.
- Exactly where the water shows, such as the gap above the window trim.
- The age of the bay window unit, if you know it.
- Whether water drips steadily or only seeps during rain.
- What the cap or flashing over the bay looks like, cracked, separated or just stained.
Common questions
- My window only leaks when it rains.
Rain-only water is coming from outside, and the usual cause is failed sealant or flashing where the bay roof meets the wall. A pro reseals that joint and resecures the flashing, and the window usually stays. The window itself is the problem only when it no longer closes or seals.
- The gap above my window trim gets wet in storms.
Water running down the wall to the trim is entering higher up and tracking behind it. The joint to fix is on the outside, at the bay roof and the window edge. Sealing the gap inside the room traps the water instead of stopping it.
- Do I need a new bay window or just a repair?
Most bay window leaks are a repair on the exterior joint, and the unit stays. Replace the unit only when the frame is bent, the glass or seals have failed, or it no longer closes and keeps water out. A soft or rotted frame caught early can be repaired with new trim and flashing.
- Can I just caulk the leak myself?
A new bead of sealant fixes a leak when the flashing is sound and you can reach the joint safely. It fails when the flashing is loose or rusted, because sealant over bad flashing splits again within a season. Anything above the first floor or on the bay roof is a hire, not a ladder job.
- Water is dripping from the ceiling above my bay window.
Water above the window means it has travelled along framing before it showed. Press the ceiling and the wall. Soft or stained material has to be opened and dried, and the exterior joint fixed before the inside is patched. A leak that keeps showing on dry days points at plumbing instead.
